Where to get a Mercedes ECU ME 9.7 for programming?

Here is all about Mercedes-Benz ME 9.7 read and write, programming:
Where to buy a new Mercedes ECU ME 9.7:
Why do you need a new ECU ME 9.7 for Mercedes?
What is Mercedes ECU ME 9.7 used for?
How to use Ktag for Mercedes ME 9.7?
Possible to use the ME 9.7 on VVDI-MB? How to?
In detail...
Where to buy a new Mercedes ME9.7 ECU ECM Engine Computer:


Why do you need a new ECU ME 9.7 for Mercedes?
Because with Me9.7 ecu, you can
- Replace the ECU with used module.
- Unlock an used ME9.7 ECM in order to adapt it with SDS, Autologic, etc.
- Can be used with Kess v2, Ktag for ecu programming
- Can be used with VVDI MB to read data
- No need for additional programming, just install the new ECM and the car will start!

What is Mercedes ECU ME 9.7 used for?
It can be used on Mercedes-Benz:

Series	Models	Chassis NO	Engine Model（ME9.7）
C Series	C230	203.052	272.920
C Series	C280	203.054	272.940
C Series	C280	204.054	272.947
E Series	E350	211.056	272.964
E Series	E280	211.054	272.943
E Series	E300	12.054	272.952
E Series	E350	207.356	272.961
CLK cars	CLK280	209.354	272.940
CLK cars	CLK350	209.356	272.960
CLS sports cars	CLS350	219.356	272.964
CLS sports cars	CLS300	219.354	272.943
SLK sports cars	SLK280	171.454	272.942
SLK sports cars	SLK350	171.456	272.963
S Series	S350	221.56	272.965
S Series	S4100	221.195	272.974
M Series	ML350	164.186	272.967
M Series	ML300	164.182	272.945
R Series	R350	251.165	272.967
R Series	R300	251.154	272.945
GLK cars	GLK300	204.981	272.984
GLK cars	GLK350	204.987	272.971

How to use Ktag for Mercedes ME 9.7?
Test: Ktag on ME 9.7 Mercedes S350 2006
Tool: Ktag programming tool China clone
Car: Mercedes S350 (W211) 2006
ECU: Bosch ME 9.7
Procedure:
Select a model in KTag software

IMPORTANT: make a backup copy of the ECU
Connect the ECU to the Ktag programmer
Pin 2 = GND
Pin 15, 16 = +12V

Ktag is gonna to read Bosch Me 9.7 Mercedes (P102)

Success! Then save data.
Result: Ktag can read Me 9.7 Mercedes without any issue!
Possible to use the ME 9.7 on VVDI-MB? How to?
Purpose: Read Mercedes Me 9.7 ECU data
Tool: VVDI MB Tool
How to:
Connect the cables from VVDI MB tool OBD to ECU directly and give power supply. Every function is fine.
If you using Benz ECU test adapter cable, please check did the can high and can low of the plug is short circuit. Some times there will have short circuit on the serial port of the ECU adapter.
In my case I’m not using resistance.
Scheme:
Mercedes-Benz ME9.7 connected to data read from ECU, did not try to reset. Check the scheme of connection
OBD2 side:

Pin Number	Pin Name	Description
1	K-Line	Ignition control (EZS), air-conditioner (KLA), PTS, safety systems (Airbag, SRS, AB) and some other
3	TNA	TD engine rotation speed
4,5	GND	Ground
6	CAN-high	CAN-High (including AirBag system in W203, W209, W220, W240, R230, ?215 after 2004y)
7	K-Line	Engine control diagnostic (ME/M***/CDI)
8		Ignition,…
9	K-Line	ABS, ASR, ESP, ETS, BAS diagnostic
11	K-Line	Gearbox and other transmission components (EGS, ETC, FTC)
12	K-Line	All activity module (AAM), Radio (RD), ICS, …
13	K-Line	AB diagnostic – safety systems
14	CAN-Low	CAN
15	K-Line	IC, KI), TAU, LWR diagnostic
16	+12V	Power

ECU Side:
2: Ground
15 & 16: 12 Volts
41: CAN High
54: CAN Low

Original:Where to get a Mercedes ECU ME 9.7 for programming?